CUTTING TOOLS AND OPERATIONS MCQ PART-3 FOR SEM 1

1) The Suitable cutting fluid for drilling M.S. plate is

compressed air

water

dry

soluble oil

2) The commonly used standard length of a hacksaw blade is

100 mm

150 mm

250 mm 

200 mm

3) The distance a drill advances into the job in one complete revolution is known as

feed 

r.p.m

machine speed

cutting speed

4) Which one of the following is used to hold the straight shank drill having a diameter less than 12 mm?

Drill drift

Socket

Drill Chuck

Sleeve

5) The rate of feed depends upon

the material of tool (drill)

material to be drilled

finish required 

all the above

6) Which among the following is NOT the factor for selection of cutting speed and feed for reaming a hole with a machine reamer?

Diameter (size) of the reamer.

The rigidity of the fixture.

The material of the job.

The material of the reamer.

7) A nut is to be made for a screw of M10 x 1.5. What should be the size of the drilled hole?

8.5 mm

9.0 mm

9.5 mm

10.0 mm

8) Which among the following factors will NOT influence the selection of the cutting speed while performing an operation on a drilling machine?

Width of job

Material of tool

Material of job

The operation to be performed

9) The reamer teeth and spacing are designed to assist in reaming more accurate holes with good surface finish. Which one of the following is true regarding the number of teeth and their spacing?

An uneven number of teeth and uneven spacing

An uneven number of teeth and even spacing

Even the number of teeth and uneven spacing

Even the number of teeth and even

10) which among the following is an artificial abrasive?

corundum

Diamond

Emery

Aluminum Oxide

11) The angle of drill grinding gauge is

59°

118°

124°

121°

12) A die nut is nothing but

a nut for tightening the die in the die stock

a die which is used for cutting threads in nuts

a nut forged by using dies

a die in the shape of a nut

13) A warding file is similar to

flat file but uniform in width

hand file but narrow in width

flat file but thinner and uniform in thickness

flat file but thinner in thickness

14) The taper shank of a drill of 20 mm diameter has

MT-1 taper

MT-2 taper

MT-3 taper

MT-4 taper

15) For grinding carbide materials

Silicon carbide wheel is used

The diamond wheel is used

Aluminum oxide wheel is used

Corundum wheel is used

16) Hacksaw blades with fine-pitched teeth are more effective on

non-metals

thin section metal

soft metals

broad section metals

17) When threading a blind hole, the third (finisher) tap is used  

to form the threads easily

to start the threads

after the first (rougher) tap 

to thread the hole with full threads up to the bottom

18) In case of a single cut file, the teeth are cut on the file face at an angle of

45° to the center line of the file

60° to the center line of the file

75° to the center line of the file

80° to the center line of the file

19) A short reamer with an axial hole used with an arbor or mandrel is called

chucking reamer

parallel reamer

expansion reamer

adjustable reamer

20) The material of twist drill is generally

H.S.S

Diamond

Carbide steel

Cast steel 

21) The best position to hold the job in the vice when filing is

shoulder level

arm level

elbow level

eye level

22) Which one among the following is NOT the cause for a broken tap while tapping?

Smaller tap drill size is used

The tap has coarse threads

Cutting oil is not used

Too much downward pressure is applied

23) What will happen if the job is loosely fitted between centers in cylindrical grinding?

The job will not rotate

The job will be thrown out

The job will be oversized

The job will be out of round

24) The cause for glazing of a grinding wheel is

a) grain size is too fine

b) wheel is hard.

c) wheel speed is too fast

d) 'A’ and ‘B’ both

25) Which one of the following bonds is most commonly used on grinding wheels?

Vitrified

Rubber

Shellac

Silicate