MCQ1. The line passing through points of zero declination is known as
(A) isogonic line
(B) agonic line
(C) magnetic line
(D) Azimuth
MCQ2. When differential leveling is done in order to connect a bench mark to the starting point of the alignment of any road, railway, canal project, it is called
(A) Profile leveling
(B) Cross-section leveling
(C) Reciprocal leveling
(D) Fly leveling
MCQ3. Contour lines meeting at a point indicate
(A) Vertical cliff
(B) Uniform space
(C) Hillock
(D) Steep slope
MCQ4. In the equation of a planimeter, ‘N’ is ______, when zero of the dial passes the index mark in a clockwise direction
(A) + ve
(B) - ve
(C) 0
(D) None of the above
MCQ5. R.L. of point ‘A’ is 50 m and R.L. of point ‘B’ is 46.655 m. The distance between AB is 150 m. The gradient of line AB is
(A) 1 in 6726 (Rising)
(B) 1 in 6726 (Falling)
(C) 1 in 3000 (Rising)
(D) 1 in 3000 (Falling)
MCQ6. The timber piece whose breadth and thickness exceed 50 mm, but are less than 200 mm in length is called
(A) Pole
(B) Baulk
(C) Scantling
(D) Batten
MCQ7. The glass articles, after manufactured, are to be cooled down slowly and gradually. The process of slow and homogeneous cooling of glass articles is
known as
(A) Annealing
(B) Blowing
(C) Rolling
(D) Spinning
MCQ8. When the final coat of paint has not sufficient opacity, the background is clearly seen. This is known as
(A) Grinning
(B) Bloom
(C) Wrinkling
(D) Flaking
MCQ9. Following is not the process involved in the fabrication of articles of plastic
(A) Laminating
(B) Blowing
(C) Calendering
(D) Tempering
MCQ10. ______ porcelain contains 70% to 90% silicate of magnesia
(A) Cordierite
(B) Zircon
(C) Carbon and graphite
(D) Steatic
MCQ11. The ______ in excess makes the cement unsound and causes the cement to expand and disintegrate
(A) Silica
(B) Alumina
(C) Magnesia
(D) Lime
MCQ12. ______ are used to finish concrete surfaces such as bridge floors, road slabs, station platforms etc.
(A) Immersion vibrators
(B) Surface vibrators
(C) Form vibrators
(D) Internal vibrators
MCQ13. In case of big projects, a certain amount to the extent of about 1.5% to 2% of the estimated cost is provided in the estimate as
(A) Work charged establishment
(B) Revised estimates
(C) Supplementary estimate
(D) Annual estimate
MCQ14. In rate analysis, the unit of measurement Indian W.C. size 580 mm size is
(A) Kg
(B) Number
(C) Pair
(D) Sq.meter
MCQ15. Certain amounts such as water supply fittings, sanitary fittings, door and window fittings, etc. are to be decided by the architect in consultation with his client at some future date. The details of such items are not worked out at the time of inviting tenders, but for execution of such items, a lump sum amount is put up in the bill of quantities. This amount is known as
(A) Prime cost
(B) Provisional sum
(C) Spot amount
(D) Deviated cost
MCQ16. Surface tension is expressed in
(A) N/m
(B) N/m2
(C) N2/m
(D) N/m3
MCQ17. The scale effects in models can be
(A) Positive only
(B) Negative only
(C) Both positive and negative
(D) None of the above
MCQ18. ______ is the square root of the ratio of the inertia force to the pressure force
(A) Reynolds number
(B) Mach’s number
(C) Euler’s number
(D) Froude’s number
MCQ19. The momentum correction factor ‘β’ is used in account for
(A) Change in direction of flow
(B) Change in total energy
(C) Non-uniform distribution of velocities at inlet and outlet section
(D) Change in mass rate of flow
MCQ20. A flow net is a graphical representation of stream lines and equipotential
lines such that these lines
(A) Intersect each other orthogonally curvilinear squares
(B) Intersect each other at various different angles forming irregular-shaped nets
(C) Indicate the direction and magnitude of vector
(D) None of above
(A) isogonic line
(B) agonic line
(C) magnetic line
(D) Azimuth
MCQ2. When differential leveling is done in order to connect a bench mark to the starting point of the alignment of any road, railway, canal project, it is called
(A) Profile leveling
(B) Cross-section leveling
(C) Reciprocal leveling
(D) Fly leveling
MCQ3. Contour lines meeting at a point indicate
(A) Vertical cliff
(B) Uniform space
(C) Hillock
(D) Steep slope
MCQ4. In the equation of a planimeter, ‘N’ is ______, when zero of the dial passes the index mark in a clockwise direction
(A) + ve
(B) - ve
(C) 0
(D) None of the above
MCQ5. R.L. of point ‘A’ is 50 m and R.L. of point ‘B’ is 46.655 m. The distance between AB is 150 m. The gradient of line AB is
(A) 1 in 6726 (Rising)
(B) 1 in 6726 (Falling)
(C) 1 in 3000 (Rising)
(D) 1 in 3000 (Falling)
MCQ6. The timber piece whose breadth and thickness exceed 50 mm, but are less than 200 mm in length is called
(A) Pole
(B) Baulk
(C) Scantling
(D) Batten
MCQ7. The glass articles, after manufactured, are to be cooled down slowly and gradually. The process of slow and homogeneous cooling of glass articles is
known as
(A) Annealing
(B) Blowing
(C) Rolling
(D) Spinning
MCQ8. When the final coat of paint has not sufficient opacity, the background is clearly seen. This is known as
(A) Grinning
(B) Bloom
(C) Wrinkling
(D) Flaking
MCQ9. Following is not the process involved in the fabrication of articles of plastic
(A) Laminating
(B) Blowing
(C) Calendering
(D) Tempering
MCQ10. ______ porcelain contains 70% to 90% silicate of magnesia
(A) Cordierite
(B) Zircon
(C) Carbon and graphite
(D) Steatic
MCQ11. The ______ in excess makes the cement unsound and causes the cement to expand and disintegrate
(A) Silica
(B) Alumina
(C) Magnesia
(D) Lime
MCQ12. ______ are used to finish concrete surfaces such as bridge floors, road slabs, station platforms etc.
(A) Immersion vibrators
(B) Surface vibrators
(C) Form vibrators
(D) Internal vibrators
MCQ13. In case of big projects, a certain amount to the extent of about 1.5% to 2% of the estimated cost is provided in the estimate as
(A) Work charged establishment
(B) Revised estimates
(C) Supplementary estimate
(D) Annual estimate
MCQ14. In rate analysis, the unit of measurement Indian W.C. size 580 mm size is
(A) Kg
(B) Number
(C) Pair
(D) Sq.meter
MCQ15. Certain amounts such as water supply fittings, sanitary fittings, door and window fittings, etc. are to be decided by the architect in consultation with his client at some future date. The details of such items are not worked out at the time of inviting tenders, but for execution of such items, a lump sum amount is put up in the bill of quantities. This amount is known as
(A) Prime cost
(B) Provisional sum
(C) Spot amount
(D) Deviated cost
MCQ16. Surface tension is expressed in
(A) N/m
(B) N/m2
(C) N2/m
(D) N/m3
MCQ17. The scale effects in models can be
(A) Positive only
(B) Negative only
(C) Both positive and negative
(D) None of the above
MCQ18. ______ is the square root of the ratio of the inertia force to the pressure force
(A) Reynolds number
(B) Mach’s number
(C) Euler’s number
(D) Froude’s number
MCQ19. The momentum correction factor ‘β’ is used in account for
(A) Change in direction of flow
(B) Change in total energy
(C) Non-uniform distribution of velocities at inlet and outlet section
(D) Change in mass rate of flow
MCQ20. A flow net is a graphical representation of stream lines and equipotential
lines such that these lines
(A) Intersect each other orthogonally curvilinear squares
(B) Intersect each other at various different angles forming irregular-shaped nets
(C) Indicate the direction and magnitude of vector
(D) None of above
No comments:
Post a Comment